version_info

Version 7.51.11.67 (December 05, 2024)
Version 7.51.11.65 (December 05, 2024)
Version 7.51.11.63 (October 21, 2024)
Version 7.51.11.62 (December 05, 2024)
Version 7.51.11.61 (December 05, 2024)
Version 7.51.11.59 (October 11, 2024)
Version 7.51.11.55 (October 07, 2024)
Version 7.51.11.51 (October 07, 2024)
Version 7.51.11.49 (October 07, 2024)
Version 7.51.11.48 (October 07, 2024)
Version 7.51.11.44 (August 13, 2024)
Version 7.51.11.41 (August 12, 2024)
Version 7.51.11.40 (October 07, 2024)
Version 7.51.11.39 (August 12, 2024)
Version 7.51.11.38 (August 12, 2024)
Version 7.51.11.36 (August 12, 2024)
Version 7.51.11.34 (March 26, 2024)
Version 7.51.11.33 (March 26, 2024)
Version 7.51.11.30 (March 26, 2024)
Version 7.51.11.27 (March 11, 2024)
Version 7.51.11.25 (March 11, 2024)
Version 7.51.11.24 (March 11, 2024)
Version 7.51.11.16 (February 26, 2024)
Version 7.51.11.11 (March 08, 2024)
Version 7.41.12.9 (November 17, 2023)
Version 7.41.12.7 (October 07, 2024)
Version 7.41.12.6 (November 10, 2023)
Version 7.41.12.4 (December 04, 2023)
Version 7.41.12.13 (November 17, 2023)
Version 7.41.12.0 (November 10, 2023)
Version 7.41.11.6 (October 10, 2023)
Version 7.41.11.2 (September 19, 2023)
Version 7.41.11.12 (November 02, 2023)
Version 7.31.9 (June 14, 2021)
Version 7.31.8 (May 11, 2021)
Version 7.31.7 (August 06, 2021)
Version 7.31.68.9 (September 26, 2023)
Version 7.31.68.7 (June 23, 2023)
Version 7.31.68.4 (May 25, 2023)
Version 7.31.68.23 (September 19, 2023)
Version 7.31.68.22 (September 26, 2023)
Version 7.31.68.20 (September 26, 2023)
Version 7.31.68.2 (June 20, 2023)
Version 7.31.68.19 (September 19, 2023)
Version 7.31.68.18 (July 25, 2023)
Version 7.31.68.16 (July 19, 2023)
Version 7.31.68.15 (July 25, 2023)
Version 7.31.68.1 (May 25, 2023)
Version 7.31.68.0 (May 03, 2023)
Version 7.31.67.8 (May 25, 2023)
Version 7.31.67.5 (June 23, 2023)
Version 7.31.67.3 (April 10, 2023)
Version 7.31.67.14 (September 26, 2023)
Version 7.31.67.11 (May 10, 2023)
Version 7.31.67.1 (March 28, 2023)
Version 7.31.67.0 (November 10, 2023)
Version 7.31.66.9 (March 10, 2023)
Version 7.31.66.7 (March 10, 2023)
Version 7.31.66.5 (June 23, 2023)
Version 7.31.66.3 (September 19, 2023)
Version 7.31.66.15 (March 27, 2023)
Version 7.31.66.11 (March 28, 2023)
Version 7.31.66.1 (March 03, 2023)
Version 7.31.65.9 (February 01, 2023)
Version 7.31.65.8 (January 18, 2023)
Version 7.31.65.3 (January 11, 2023)
Version 7.31.65.0 (January 04, 2023)
Version 7.31.64.0 (December 22, 2022)
Version 7.31.63.2 (February 15, 2023)
Version 7.31.63.0 (December 08, 2022)
Version 7.31.62.3 (October 12, 2023)
Version 7.31.62.15 (April 10, 2023)
Version 7.31.62.13 (November 29, 2022)
Version 7.31.62.11 (November 29, 2022)
Version 7.31.62.1 (October 07, 2024)
Version 7.31.61.8 (October 12, 2023)
Version 7.31.61.7 (April 01, 2024)
Version 7.31.61.5 (October 19, 2022)
Version 7.31.61.1 (October 12, 2022)
Version 7.31.61.0 (February 15, 2023)
Version 7.31.60.2 (November 04, 2022)
Version 7.31.6 (April 15, 2021)
Version 7.31.59.7 (October 12, 2022)
Version 7.31.58.1 (October 12, 2022)
Version 7.31.57.5 (August 30, 2022)
Version 7.31.57.2 (January 12, 2023)
Version 7.31.57.0 (September 07, 2022)
Version 7.31.56.2 (February 15, 2023)
Version 7.31.55.3 (September 19, 2023)
Version 7.31.55.0 (November 29, 2022)
Version 7.31.54.0 (August 30, 2022)
Version 7.31.53.7 (November 29, 2022)
Version 7.31.53.6 (June 20, 2023)
Version 7.31.53.3 (July 07, 2022)
Version 7.31.53.1 (November 29, 2022)
Version 7.31.51.2 (April 10, 2023)
Version 7.31.51.0 (June 20, 2022)
Version 7.31.50.0 (May 03, 2022)
Version 7.31.5 (August 06, 2021)
Version 7.31.49.6 (April 26, 2022)
Version 7.31.49.5 (July 07, 2022)
Version 7.31.49.4 (April 18, 2022)
Version 7.31.49.2 (March 13, 2023)
Version 7.31.49.0 (May 03, 2022)
Version 7.31.48.6 (August 19, 2022)
Version 7.31.48.4 (June 24, 2022)
Version 7.31.48.1 (April 12, 2022)
Version 7.31.48.0 (March 22, 2022)
Version 7.31.47.7 (March 21, 2022)
Version 7.31.46.4 (March 08, 2022)
Version 7.31.46.3 (March 08, 2022)
Version 7.31.46.1 (April 12, 2022)
Version 7.31.46.0 (March 30, 2022)
Version 7.31.45.1 (August 03, 2022)
Version 7.31.45.0 (April 05, 2022)
Version 7.31.44.1 (February 07, 2022)
Version 7.31.44.0 (August 03, 2022)
Version 7.31.43.1 (January 26, 2022)
Version 7.31.43.0 (March 08, 2022)
Version 7.31.42.0 (January 21, 2022)
Version 7.31.41.1 (August 03, 2022)
Version 7.31.41.0 (April 12, 2022)
Version 7.31.4 (May 16, 2023)
Version 7.31.39.0 (September 07, 2022)
Version 7.31.38.3 (January 03, 2022)
Version 7.31.38.2 (December 03, 2021)
Version 7.31.38.1 (February 07, 2022)
Version 7.31.38.0 (December 01, 2021)
Version 7.31.37.2 (December 01, 2021)
Version 7.31.37.0 (November 08, 2021)
Version 7.31.36.0 (November 12, 2021)
Version 7.31.35.0 (November 02, 2021)
Version 7.31.34.1 (January 12, 2023)
Version 7.31.33.2 (October 14, 2021)
Version 7.31.32.5 (February 11, 2022)
Version 7.31.32.4 (April 28, 2022)
Version 7.31.32.3 (October 18, 2021)
Version 7.31.32.2 (December 01, 2021)
Version 7.31.32.0 (October 05, 2021)
Version 7.31.30.2 (September 22, 2021)
Version 7.31.30.1 (September 22, 2021)
Version 7.31.30.0 (September 22, 2021)
Version 7.31.3 (August 23, 2022)
Version 7.31.29.3 (September 16, 2021)
Version 7.31.29.2 (September 13, 2021)
Version 7.31.29.0 (September 16, 2021)
Version 7.31.28.1 (November 02, 2021)
Version 7.31.28 (December 01, 2021)
Version 7.31.27 (February 07, 2022)
Version 7.31.25 (October 13, 2021)
Version 7.31.24 (October 04, 2021)
Version 7.31.23 (September 07, 2022)
Version 7.31.22 (August 23, 2021)
Version 7.31.21 (August 05, 2021)
Version 7.31.20 (August 23, 2021)
Version 7.31.2 (March 08, 2022)
Version 7.31.19 (September 26, 2023)
Version 7.31.18 (June 16, 2021)
Version 7.31.17 (November 29, 2022)
Version 7.31.16 (July 13, 2021)
Version 7.31.15 (June 14, 2021)
Version 7.31.14 (May 25, 2021)
Version 7.31.12 (October 04, 2021)
Version 7.31.11 (April 18, 2022)
Version 7.31.1 (February 16, 2021)
Version 7.31.0 (February 11, 2021)
Version 7.30.9 (February 12, 2021)
Version 7.30.8 (February 15, 2021)
Version 7.30.7 (February 10, 2021)
Version 7.30.6 (August 13, 2021)
Version 7.30.5 (March 17, 2021)
Version 7.30.2 (February 02, 2021)
Version 7.30.0 (August 05, 2021)
Version 7.20.37 (March 22, 2021)
Version 7.20.36 (April 23, 2021)
Version 7.20.25 (August 08, 2022)
Version 7.20.24 (July 07, 2022)
Version 7.20.23 (April 23, 2021)
Version 7.12.93 (October 07, 2024)

Version 7.51.11.67 (December 05, 2024)

New feature: Added new feature in Config/Conversion for setting project folder to import folder
Bug fix: CDT_112824_1803_JCP – Some holes are missing some circles
Bug fix: EXP_120224_1256_JCP – Waterline to drill and Oil line to drill won't export to iges (use waterline to drill at .175)
Bug fix: PST_112824_1854_JCP – It appears that the ATC model function is not saving correctly after trying to reset to default in the WD folder

Version 7.51.11.65 (December 05, 2024)

Bug fix: PRL_110624_1859_JCP – Problem with the process list

Version 7.51.11.63 (October 21, 2024)

Bug fix: PRB_101724_2043_JCP – fixed indentification of angled holes for Probe Check Function
Bug fix: DOC_101524_1336_JCP – fixed missing holder info in ISO document
Bug fix: – fixed total assembly length in Tool Database/Assembly tab
Bug fix: PRB_102424_1348_JCP – Check Probing is selecting angled holes that are not on the plane selected

Version 7.51.11.62 (December 05, 2024)

Bug fix: PRB_101724_2043_JCP – Probing check is not seeing angled holes anymore

Version 7.51.11.61 (December 05, 2024)

Bug fix: DOC_101524_1336_JCP – Problem with documentation for ISO – test.docx is what the customer would like

Version 7.51.11.59 (October 11, 2024)

New feature: Added new feature in Config/Conversion for setting project folder to import folder
Bug fix: MSC_100724_1913_JCP – Problem With Create Spotface – please see video zipped in attachment

Version 7.51.11.55 (October 07, 2024)

Bug fix: DRL_091824_0104_JCP – Problem with no calc in Multidrill
Bug fix: PRB_091824_0114_JCP – Problem with Check Probe Points on plates

Version 7.51.11.51 (October 07, 2024)

Bug fix: FIX_082224_1205_JCP – Problem with Fixture function

Version 7.51.11.49 (October 07, 2024)

Bug fix: COL_071124_1500_JCP – Collision test is asking to save the holder db each time
Bug fix: CAD_071524_1625_JCP – Cad Curve not being rotated correcty
Bug fix: DOC_072324_1327_JCP – Problem with Max Depth Doc the problem exists with any Rtm file

Version 7.51.11.48 (October 07, 2024)

Bug fix: DRL_071724_1553_AJR – Z Security Optimize Problem Probing

Version 7.51.11.44 (August 13, 2024)

Bug fix: PRL_053024_1707_JCP – Add modify parameters to Process List

Version 7.51.11.41 (August 12, 2024)

Bug fix: DDB_051324_1533_JCP – Problem with specify colour patterns staying tagged after saving closing and reopening …

Version 7.51.11.40 (October 07, 2024)

Bug fix: STK_050224_1355_JCP – Unable to export stock model to STL
Bug fix: PRB_050224_1548_JCP – Problem with probe point filter

Version 7.51.11.39 (August 12, 2024)

Bug fix: DRL_042524_1502_JCP – Problem with Extremity stock
Bug fix: DDB_041824_0049_JCP – Problem with specify colour

Version 7.51.11.38 (August 12, 2024)

Bug fix: MPL_040324_2054_JCP – Multiplate is using the wrong information for the <PATH> varaible
Bug fix: MPL_040224_1931_JCP – Add name of model as default in MultiPlate when posting

Version 7.51.11.36 (August 12, 2024)

Bug fix: GDR_032724_1412_JCP – Problem with creation order in gundrilling
Bug fix: DRL_032624_1328_JCP – Not able to make a reference with a Negative A

Version 7.51.11.34 (March 26, 2024)

Bug fix: DRL_031224_1251_JCP – MutliDrill Is dropping out and not making a program

Version 7.51.11.33 (March 26, 2024)

Bug fix: DDB_030424_1522_JW – When you create a new pattern it no longer pops up with the Drill database with the New_Drill Pattern window. You have to select from the list. Once created we no longer tag the holes.
Bug fix: TAG_022624_1721_JW – When a new pattern is created we are not auto detecting them. You have to go and select Tag All. Used to automatically tag the new patterns
Bug fix: MSC_030624_1856_JW – When using UDC11 to UDC15 the gen post will not allow the post to save. If these are changed between UDC1 to UDC10 works fine.
Bug fix: STK_030424_1622_JW – When a drill has been used and updated in the stock model we are not removing it when it is recalculated like a 3D program.
Bug fix: PRB_030624_1907_JCP – In the latest version, I am not able to use the HoleCheck probing as it sqays there are no probe points in the database

Version 7.51.11.30 (March 26, 2024)

Bug fix: DDB_022224_1530_JCP – Slight mods to the specify pattern with color
Bug fix: PST_022124_1407_JCP – Problems with new ATC doc

Version 7.51.11.27 (March 11, 2024)

Bug fix: STK_020924_1423_AJR – Collision Check with Stock Model Problem

Version 7.51.11.25 (March 11, 2024)

Bug fix: MSC_020724_1426_JCP – Extenson slider bar works great, but we are not able to type a negative number into the textbox

Version 7.51.11.24 (March 11, 2024)

Bug fix: MSC_012824_1758_JCP – Add new column in ATC manager to allow for a “print” attribute
Bug fix: STK_012824_0023_JCP – Add Stock model update check box to drill manager operations
Bug fix: PRB_012824_1818_JCP – A New attribute to probe point to link it to an operation
Bug fix: DRL_012824_1742_JCP – New Feature called “Specify Colour”
Bug fix: DRL_012824_1748_JCP – Change function “copy pattern macro” to just “copy macro”

Version 7.51.11.16 (February 26, 2024)

Bug fix: STK_121923_1722_JW – Request-Paulo- Would like to have the option to remove a file from the stock model without having to exit the toolpath screen.

Version 7.51.11.11 (March 08, 2024)

Bug fix: LCT_022124_2358_RAO – In the Pamameter file the Distance3D seems to be broken in V7. Maybe just an interface issue?

Version 7.41.12.9 (November 17, 2023)

Bug fix: MSC_111423_2010_JCP – Probe “IPROB” number output in post doesn't match ID in XML file.

Version 7.41.12.7 (October 07, 2024)

Bug fix: IMP_110623_1613_JCP – Problems with DWG import – text placement and duplicate output
Bug fix: MSC_110623_1325_JW – When using Seperate by Tool would like to use “-” instead of “_ ” due to some machines ability to read certain characters. Or give the option to change it.
Bug fix: ZCS_110923_1545_JW – Z-Cut Solid cutting outside the selected window. Causing the cutter to cut into raw material- Rob Olsen submitted same issue alreadyZCS_101023_1233_JCP. Just another example.

Version 7.41.12.6 (November 10, 2023)

Bug fix: MSC_110723_1455_AJR – Cavalier file wont load
Bug fix: MSC_102623_2028_JCP – Problem opening new file with version 7.31.55.4

Version 7.41.12.4 (December 04, 2023)

Bug fix: CVP_110123_1450_JW – Curve 2D is cutting through th part when a Vertical Chamfer\Fillet is added. Does warn about the violation.
Bug fix: PST_102323_1415_JCP – Add a new checkbox to separate files by tool, only when posting from the process list.

Version 7.41.12.13 (November 17, 2023)

Bug fix: STP_111623_1303_JW – Verification window does not appear when selecting Alternate Rotation.

Version 7.41.12.0 (November 10, 2023)

Bug fix: ZCS_101023_1233_JCP – Zsolid entries are outside the window causing a problem

Version 7.41.11.6 (October 10, 2023)

Bug fix: DRL_092723_1547_JCP – Problem with drill macro, no mil files are produced
Bug fix: EXP_092723_1548_JCP – In the new function to export pocket profile to iges, please allow the user to select several pocket and output to one iges file and also ouput the iges file to the current cam reference in the pocket manager

Version 7.41.11.2 (September 19, 2023)

Bug fix: DDB_091223_2204_JCP – Problem with odd characters in the XML drill manager status file

Version 7.41.11.12 (November 02, 2023)

Bug fix: ZPT_100623_1231_AJR – Collision Not Detected After Switching Machine
Bug fix: CBN_101623_1756_AJR – Curve Milling in 3D Problem
Bug fix: IMP_100523_1645_JCP – Please add the extension .DWG (AutoCAD) to the translator list – it is supported by Datakit – Sample for translation included

Version 7.31.9 (June 14, 2021)

Bug fix: STK_041921_2038_JCP – Stock Model import problems from Powermill – both files, nothing happens. No result and no error
Bug fix: DOC_042121_2034_JCP – We still have a problem with the documentation
Bug fix: MPL_042221_1950_JCP – Multiplate is skipping files

Version 7.31.8 (May 11, 2021)

Bug fix: CAD_042221_1648_JW – Translate option-“Move” a point or suface uses current origin system. “Copy” the same point or surface and it uses the Orginal cordinate system.
Bug fix: DOC_041221_2114_JCP – Capture from the ISO documentation not working
Bug fix: GRA_041521_2114_JCP – Can't pick pocket when there is a larger pocket over top
Bug fix: V2D_041521_2109_JCP – Volumill 2d recalc with Drill entry not working
Bug fix: DRL_041221_1253_JCP – Problem with Zsecurity in Multidrill
Bug fix: SIM_041221_2048_JCP – C only rotations are not displaying or collision checking correctly

Version 7.31.7 (August 06, 2021)

Bug fix: GRA_040821_1528_JW – When you try and select the Start point and end point of a curve the model is very difficult to see. Would like to make the model brighter.
Bug fix: DRL_040821_1416_JCP – Multi drill doesn't work if more than one type of pattern selected
Bug fix: PST_041221_1542_JW – When you create the first setup the post will not post the G cycle. It is posting out Point to point. Create the second setup and it will post the Gcycles out correctly.
Bug fix: PST_040621_1649_JCP – Problem with the ouput value for <ZBUSH> when rotated
Bug fix: MSC_040621_1830_JCP – Entry inc is not being respected from the Parameter file – we had this problem in a bug not long ago – it's back!
Bug fix: ZCS_040521_1353_JCP – Collision Avoidance has a Collisiion detected

Version 7.31.68.9 (September 26, 2023)

Bug fix: MPL_062123_1451_JCP – Mutliplate is not outputting ISO file
Bug fix: MSC_062123_2131_JCP – When creating a new reference, the new reference should be 0,0 but is coming in as 90,0
Bug fix: MSC_062023_0043_JCP – Problem with model dimensions in post
Bug fix: ZPT_062723_1432_JCP – ZPart is very slow in 7.31.68.9 – no problem in 7.31.68.8
Bug fix: PK2_062923_1437_JCP – Bad Entry in Pocketing
Bug fix: PRB_062823_2357_JCP – Problem with Probe check function finding points below the indicated surface
Bug fix: MSC_061623_1643_JCP – Colour hints missing from color pallet
Bug fix: PST_061323_1237_JCP – Problem with ABS output in post

Version 7.31.68.7 (June 23, 2023)

Bug fix: MSC_053023_1500_JCP – Corrupt 3d tree

Version 7.31.68.4 (May 25, 2023)

Bug fix: MSC_052423_1535_JCP – Please add the functionality that when we change machines, temporarily updat the reference for simulating and collision check
Bug fix: ZPT_051923_1614_JCP – Option missing from Zpart
Bug fix: DRL_052323_1653_JCP – Problem with Multidrill
Bug fix: MSC_051823_1656_JCP – Can't import Tool xls file – I get a dbinterface error.

Version 7.31.68.23 (September 19, 2023)

Bug fix: PST_090123_1414_JCP – Add a checkbox in the config to override posting from different setups – we need to allow this for some Italian and Portugese customers

Version 7.31.68.22 (September 26, 2023)

Bug fix: ZSP_082823_1955_JCP – Problem with identical pockets not calculating correctly in the pocket manager –
Bug fix: EXP_082823_1756_JCP – This is a request to right click on a pocket and export the top profile of the pocket as lines and arcs in Iges.
Bug fix: PST_081623_1400_JCP – The posted file is not outputting the correct angle.
Bug fix: PK2_082823_1749_JCP – The Zsecurity is set correctly, and is good after making the program. If you change the pocket top ot bottom, the Zsecurity lifts a lot.

Version 7.31.68.20 (September 26, 2023)

Bug fix: PED_072023_2112_JCP – When adding a top fillet or chamfer after a bottom chamfer – the top height remembers old height settings – please see attached video

Version 7.31.68.2 (June 20, 2023)

Bug fix: ZCS_051523_1314_JCP – Missing slices in Zsolid

Version 7.31.68.19 (September 19, 2023)

Bug fix: PRB_071723_1701_JCP – Probe points missing in the new function “Insert probe points check”
Bug fix: ZPT_071823_2333_JCP – ZPart doesn't machine one side when using the stock model
Bug fix: GRA_071623_1351_JCP – Problem with colour palette causing dll error

Version 7.31.68.18 (July 25, 2023)

Bug fix: UDC_071723_1646_JCP – Please make a decortic output instead of a warning if a post processor doesn't have UDC cycles filled in

Version 7.31.68.16 (July 19, 2023)

Bug fix: PK2_070623_1625_JCP – Problem in Pocketing with tapered or drafted walls
Bug fix: PRB_070923_1740_JCP – Insert Probe point is putting double points with one click
Bug fix: GRA_070623_2041_JCP – Problem with colour pallet.

Version 7.31.68.15 (July 25, 2023)

Bug fix: GRA_070423_1615_JCP – True colour in the config like the true colour in the display
Bug fix: GDR_070423_2130_JCP – Problem with final depths in multidrill

Version 7.31.68.1 (May 25, 2023)

Bug fix: PK2_050923_1655_JCP – Bad Move inside pocket 2d
Bug fix: GRA_050923_1644_JCP – Problem picking pattern underneath edge of another pattern
Bug fix: HEL_050523_2117_JCP – Problem with not continuous helical

Version 7.31.68.0 (May 03, 2023)

Bug fix: PSN_050223_2143_JCP – Pocket Sectioning “pick” function is giving Global Coordinates instead of the Cam Reference

Version 7.31.67.8 (May 25, 2023)

Bug fix: DRL_041823_1259_JCP – Collsion detected, but not reported in the status!
Bug fix: PK2_041423_1441_JCP – Pocket Folders Not behaving correctly

Version 7.31.67.5 (June 23, 2023)

Bug fix: STK_032923_1522_JCP – Stock model doesn't update – problem occurred between 67.1 and 67.3
Bug fix: DRL_051923_1949_AJR – Collision not Detected
Bug fix: PST_051923_2027_AJR – Posted Z Security Problem
Bug fix: CAD_041023_1352_AJR – Copy Paste Internal Error
Bug fix: GDR_041323_1948_AJR – Gundrill not drilling to Depth

Version 7.31.67.3 (April 10, 2023)

Bug fix: MRG_032723_1627_JCP – When merging a file into another file (even if I just merge it by itself into a “new” RTM the status and setup are lost

Version 7.31.67.14 (September 26, 2023)

Bug fix: CAM_050423_1446_ALE – Wrong Mill File Depth using Cam Curves and picking Zstart and Zend on 3D Model
Bug fix: CAM_050423_1519_ALE – CamCurve In Wrong Position Selecting Lead In and Lead Out Points
Bug fix: MSC_050423_1003_ALE – Add To Process List Error Using DP

Version 7.31.67.11 (May 10, 2023)

Bug fix: DOC_042623_2033_JCP – Trying to produce a drill estimate produces an error.

Version 7.31.67.1 (March 28, 2023)

Bug fix: PK2_032323_1238_JCP – Problem with rabbit ears default in pocket manager - non continuous
Bug fix: GRA_032223_2006_JCP – Not Able to select pockets in the pocket manager easily.

Version 7.31.67.0 (November 10, 2023)

Bug fix: MSC_031523_1720_JCP – Request For Extension Slider Bar
Bug fix: DRL_042023_1106_RAO – Deleteing Circles after untagging produces an error to save as. This is ok in 7.31.55
Bug fix: ENG_032823_0042_RAO – Cannot Modify Engrave. Option is Grayed Out. If I rotate or select some thing elset might allow the options.
Bug fix: PK2_041223_1255_RAO – Group Name should default to folder name
Bug fix: PK2_041223_1256_RAO – Pocket Creation NOT going in folder selected as well as mirror, copy and move
Bug fix: MSC_041223_1255_RAO – Measure in All Tabs for circle info and element info not using current ref and always uses global
Bug fix: DOC_040623_1932_RAO – V7 ATC Document Creation NOT Same as V6
Bug fix: ZPT_033123_1329_RAO – Zpart Arc entry not working as expected needs to be like ramp cutter path Changing parameter fixed issue but calculation time is much longer
Bug fix: GRA_031723_1729_JCP – Add or Move Circle Zoom Problem
Bug fix: CAD_031023_1625_JCP – Create box should only look at surfaces
Bug fix: MSC_031423_1155_JCP – More Translation ID missing (last ones :))
Bug fix: DRL_032223_1338_JCP – Extremity stock is not behaving correctly for inclined holes

Version 7.31.66.9 (March 10, 2023)

Bug fix: PSN_022723_1612_JCP – Manual Zsection is not using the current reference for Z
Bug fix: DRL_022723_1520_JCP – Request to truncate drilling in all cases when the normal truncation ends during an intersection.

Version 7.31.66.7 (March 10, 2023)

Bug fix: DRL_022023_1931_JCP – Problem with highlight in search and replace function in drill manager
Bug fix: PST_022023_2104_JCP – Problem with model dimensions in posted file.

Version 7.31.66.5 (June 23, 2023)

Bug fix: PK2_022823_1352_JCP – Pocket remachine not starting in the correct position
Bug fix: GRA_022823_1404_JCP – Saving progress bar is not working.

Version 7.31.66.3 (September 19, 2023)

Bug fix: ZCS_022123_1810_AJR – Missing Slices
Bug fix: MSC_020623_1905_JCP – Translate messages – missing ID's – please upzip the attachment to see the missing ID's
Bug fix: ZCS_021423_1913_AJR – Missing Slices
Bug fix: PST_020323_1410_JCP – Problem with moving origin – the posted file doesn't reflect the change.
Bug fix: PST_020223_1209_AJR – Posting Issue after Switching Machine

Version 7.31.66.15 (March 27, 2023)

Bug fix: MSC_030823_1505_JCP – More Translation items for Portugal

Version 7.31.66.11 (March 28, 2023)

Bug fix: PK2_022723_2108_JCP – Pocketing changes for old version
Bug fix: DRL_022823_1449_JCP – Multidrill REcalc not selecting all holes

Version 7.31.66.1 (March 03, 2023)

Bug fix: MSC_021723_1324_JCP – Drill to surface producing points where there is no pattern
Bug fix: MSC_021623_1519_JCP – Add the option to save the point file on a different layer for the drill to surface function
Bug fix: MSC_012423_1337_JCP – Updating Mil path (and Zsecurity) when posting or recalcing programs made for another machine

Version 7.31.65.9 (February 01, 2023)

Bug fix: _012023_1912_JCP – insert probe point with new reference
Bug fix: DDB_011823_2029_JCP – Version 7.31.65.9 is having trouble opening files from 7.31.64

Version 7.31.65.8 (January 18, 2023)

Bug fix: DDB_011723_1255_JCP – Intersections appear to large/long
Bug fix: DDB_011623_1547_JCP – If you import the file, and make a setup Rtm will show an internal error

Version 7.31.65.3 (January 11, 2023)

Bug fix: LCT_010523_1905_AJR – Collision Check not checking Rapid Moves

Version 7.31.65.0 (January 04, 2023)

Bug fix: DRL_122122_2033_JCP – Extremity stock offset not applying the incline correctly
Bug fix: DRL_122122_2023_JCP – Browse tag should have the drill patterns overlay the shaded file
Bug fix: ZCS_122122_2138_JCP – Zsolid misses Collision
Bug fix: DRL_122122_2015_JCP – When using multiple tool for an operation, is one tool is removed the wrong tool is posted

Version 7.31.64.0 (December 22, 2022)

Bug fix: DRL_121522_1345_JCP – MultiDrill is crashing system
Bug fix: DRL_121322_1755_JCP – Problem with coolant ouput during posting for multiple drill lengths

Version 7.31.63.2 (February 15, 2023)

Bug fix: ZCS_121222_1336_AJR – Z-Solid Remachine Problem

Version 7.31.63.0 (December 08, 2022)

Bug fix: V2D_120522_1408_JCP – Problem with drill entry when using Volumill and Multimill in the pocket manager
Bug fix: DRL_120222_1527_JCP – Unused circles in the drill manager are not in the colour font specified in the config
Bug fix: DRL_120222_1603_JCP – Partially tagged holes are not being retagged when a new pattern is created.

Version 7.31.62.3 (October 12, 2023)

Bug fix: FLT_111122_1748_JW – Getting some unusual\erratic moves in the Dragcut program. See pics
Bug fix: STP_111722_1620_JW – Double click the setup in the pocket manager and no pockets are being displayed. It use to highlight all the pockets on that setup.
Bug fix: WDW_111722_1615_JW – Windows can be seen through the job from the opposite setups. Shading is turned on.
Bug fix: WDW_111722_1610_JW – Cannot pan the job when you are using the Rectangle windows.
Bug fix: STP_111622_1646_JCP – Unable to add a hole to any setup

Version 7.31.62.15 (April 10, 2023)

Bug fix: PK2_113022_1430_JCP – Pocketing report #3

Version 7.31.62.13 (November 29, 2022)

Bug fix: MSC_112822_1419_JCP – Collision check leaving task running with “bad geometry” error

Version 7.31.62.11 (November 29, 2022)

Bug fix: DOC_112222_2104_JCP – Problem with drillmanager xml file.

Version 7.31.62.1 (October 07, 2024)

Bug fix: STK_111022_1654_JCP – Unable to import stock model from Powermill – this one should, as it's a nice closed volume
Bug fix: MSC_110822_1843_JCP – Inside the zip file are some areas in the software that Portugal was not able to translate –
Bug fix: MSC_111022_1929_JCP – Collison checking odd result

Version 7.31.61.8 (October 12, 2023)

Bug fix: FLT_110722_1247_JW – Pocket with Ramp and Auto Entry plunges and gives a violation. Change to Ramp and Pocket Center entry works fine
Bug fix: PK2_110322_1343_JW – When you use the Zig Zag option for a 2-d pocket the program errors out.
Bug fix: FIX_111622_1441_AJR – Fixture Plate Issue
Bug fix: PKM_110322_2215_JW – Pocket Databases are not being displayed in the other databases except for the AAA(ID-428) All Machines
Bug fix: DRL_110222_2035_JCP – Zsecurity is not correct to the settings in the config.

Version 7.31.61.7 (April 01, 2024)

Bug fix: IMP_102722_1618_JW – When this IGES file is imported we are untrimming surfaces in the corners. The STEP file looks good.
Bug fix: ZCS_102622_2358_JW – When you use the Contract for the Z-Cut Solid entry violations appear. Use Expand works fine.
Bug fix: PK2_101222_2127_JW – Getting a “Mill Violation” when using the Curve 2-d on a pocket in the pocket manager.
Bug fix: STK_101422_2050_JCP – Stl Import scaling is not using enough decimal places.
Bug fix: MSC_101922_2055_JCP – Delta (Tibor) requests

Version 7.31.61.5 (October 19, 2022)

Bug fix: DOC_101022_1434_JCP – Documentation not quite correct in RTM, and not at all correct in multiplate

Version 7.31.61.1 (October 12, 2022)

Bug fix: PST_092922_1611_JCP – Model Setup dimensions are not output correctly

Version 7.31.61.0 (February 15, 2023)

Bug fix: PK2_100722_2110_AJR – Bad cutting moves in Pocket 2D
Bug fix: DDB_092822_0941_ALE – Wrong Coordinates Using Insert DP Library inside the final dialog box or every time you select ENTER key
Bug fix: STP_092822_0915_ALE – RTM doesn't update the Mill files when you change the Setup Name

Version 7.31.60.2 (November 04, 2022)

Bug fix: DRL_092222_1457_JCP – The Rtm File comes in untagged …

Version 7.31.6 (April 15, 2021)

Bug fix: PK2_032621_1652_AJR – Pocketing not warning tool too short
Bug fix: DOC_032621_1853_JCP – Drill estimate appears not to work at all
Bug fix: MPL_033121_2154_JCP – Problems with MPM

Version 7.31.59.7 (October 12, 2022)

Bug fix: IMP_091522_1330_JCP – Layers not importing from UG into RTM
Bug fix: DDB_091422_1135_ALE – Wrong Coordinates Using Insert DP Library
Bug fix: GRA_091422_1058_ALE – Graphical Comparison doen'st work correctly
Bug fix: DDB_091422_1157_ALE – Prefix Operation Name During DP Library Creation
Bug fix: MSC_091522_1326_JCP – Please allow the the following characters in the setup name ()[];

Version 7.31.58.1 (October 12, 2022)

Bug fix: IMP_083122_1821_AJR – Pro Engineer Files importing wrong colour
Bug fix: IMP_082322_1506_JCP – Problem importing excel to tool db

Version 7.31.57.5 (August 30, 2022)

Bug fix: STK_081822_1541_JCP – Stock model export won't export to stl due to memory

Version 7.31.57.2 (January 12, 2023)

Bug fix: IMP_081622_1229_JCP – Importing STL file to stock model doesn't load correctly

Version 7.31.57.0 (September 07, 2022)

Bug fix: DRL_090222_1359_JW – When multiple References are select and then you right click and say drill, all angled lines are drilled straight. This should not be allowed.
Bug fix: CAD_080822_1704_JCP – This is a request to copy/paste surface/CAD data between 2 open RTM sessions.

Version 7.31.56.2 (February 15, 2023)

Bug fix: PK3_080522_1929_AJR – Z-Part Not starting at top of pocket
Bug fix: DOC_081122_1109_ALE – WRONG Setup Documentation
Bug fix: PST_081122_1011_ALE – NO Gundrill Intersection using Multiplate
Bug fix: DRL_081122_1535_JW – We are not seeing that the hole has been drilled from the opposite side of the job and we are drilling it again instead of just doing the REV operation.

Version 7.31.55.3 (September 19, 2023)

Bug fix: CAD_071223_1646_RAO – Add Surface Rectangle by Mouse not put in correct machine setup coordinates
Bug fix: SIM_082223_1349_AJR – Simulation Wrong After switching Machines
Bug fix: STP_032423_1815_AJR – Create Setup in Drilling Rotating Axis
Bug fix: MPL_100522_1703_JW – MPM not putting the * on each side of the changed tool in the ATC. Should have *7* when tool number is changed from the ATC default.
Bug fix: MPL_100622_1334_JW – When the ATC is being displayed during the MPM we need to have the Virtual Tools become Shaded\Italics or something to identify they are virtual tools.
Bug fix: GRA_100622_1405_JW – Have the Camera window default to Table Top and Table ISO instaed of the XY & Isometric2
Bug fix: GRA_100622_1545_JW – Request-Add option Interface ID so we can orginize the machines in the RTM Interface. Currently we are doing it by the machine ID and the order they are in in the Manufacturing settings.
Bug fix: V3D_080222_1500_JW – Volumill violating window boundaries. Another example..
Bug fix: V3D_080222_1443_JW – Volumill -3D is violating windows that are selected. Here you can see that we went into a window boundary and this caused the tool to break.
Bug fix: PK2_072622_2049_AJR – Rapid moves in Pocketing violate Part
Bug fix: PST_080122_2053_JCP – Problem with order of pocket machining when pockets are on top of each other.
Bug fix: MSC_080322_2312_JW – When an Assembly is modified\Updated it is not updating the Diameter,Speeds or feeds. It does update the Name odf the tool but that is it.
Bug fix: PST_080222_2145_JCP – Post Special Sequence not updating

Version 7.31.55.0 (November 29, 2022)

Bug fix: MSC_071122_1410_JCP – Collision Detection error in Helical

Version 7.31.54.0 (August 30, 2022)

Bug fix: SIM_063022_1330_JCP – Problem configuring 90 degree head
Bug fix: GDR_070522_1305_AJR – Soft Start Values not Copying with Tool
Bug fix: MSC_070722_1341_JCP – Add hint to all modules to see the name of the assembly or tool when pointing at the mil file name
Bug fix: PSN_062722_2137_AJR – User Defined Z Security Problem
Bug fix: MSC_062822_2146_JCP – Negative Stock / Variable Stock needs some changes

Version 7.31.53.7 (November 29, 2022)

Bug fix: ENG_062222_1429_JW – Cannot measure the Engraving unsing the Measure\Distance. Get a red circle with a line through it when you try and pick points. Was able to it around version 7.31.21.

Version 7.31.53.6 (June 20, 2023)

Bug fix: PK2_061722_2020_JCP – Pocketing stepover optimization problems
Bug fix: SIM_062022_1507_JCP – Simulator is crashing RTM

Version 7.31.53.3 (July 07, 2022)

Bug fix: PK2_062122_1412_JW – When you copy a group of milled pockets and then change the depth on the copied pockets or change the operations the milled pocket go back to “READY” status.
Bug fix: CFP_061622_2112_AJR – Chamfer 2D in Pocketing Rapid Issue

Version 7.31.53.1 (November 29, 2022)

Bug fix: DRL_060722_1449_AJR – Collision Not Detected

Version 7.31.51.2 (April 10, 2023)

Bug fix: ZCS_061522_1825_JW – Keep getting Missing Slices when creating the Z-Cut Solid on a .500 casted Stock Model
Bug fix: ZPT_060622_1408_JW – Z-Cut Part is violating the job. (Ruff) Cutting through the part to the bottom of the job. If i turn on the Avoid Carrort Buildup seems to work but displays the path to the bottom.
Bug fix: ZCS_082922_1501_JCP – Zsolid it missing many areas in rerough, and rerough is very very slow.
Bug fix: ZCS_060122_1518_JCP – Zsolid undetected missing slices and Zsolid entry problem
Bug fix: ZCS_050422_1422_JCP – Problem with Zsolid and improve undercut – also stock model update
Bug fix: ZCS_060122_1601_JCP – ZSolid with improve undercut won't calculate
Bug fix: STP_060122_1409_JCP – Rtm is posting an alternate angle instead of the angles shown

Version 7.31.51.0 (June 20, 2022)

Bug fix: MSC_050222_1423_JCP – Surfaces won't load – env fle corrupt

Version 7.31.50.0 (May 03, 2022)

Bug fix: MSC_042822_1800_JW – When you are selecting the curve direction it says 2D-Curve but when you are choosing the Chamfer direction it still says 2-D Curve. Should say what the program is.

Version 7.31.5 (August 06, 2021)

Bug fix: MSC_032321_1625_JCP – Pocket manager separation bar is not moveable any more.
Bug fix: PST_031921_1940_JCP – When using the feature to select by assembly, we are not unselecting well
Bug fix: PK2_031921_1935_JCP – Pocket manager refresh problem
Bug fix: PST_031921_1929_JCP – Helical is producing an unwanted line in output

Version 7.31.49.6 (April 26, 2022)

Bug fix: CVD_042022_2010_JCP – Problem with false violation in Curve2d when tapered

Version 7.31.49.5 (July 07, 2022)

Bug fix: MSC_041922_2106_JCP – Saving is taking much to long in some cases.
Bug fix: EXP_041922_1351_JCP – Export Holder Database to an XML file – I've included a sample of what I would like to get –
Bug fix: MSC_042022_1403_JCP – Dongle warning when unplugged – we should add a timer to check.
Bug fix: IMP_042122_1649_JW – When a Metric Iges file is imported it is giving an error. 2 examples are attached.
Bug fix: FLT_041822_1402_JCP – Problem with offset leaving cusps in pocket bottoms – we are not looking at the corner rad of the tool
Bug fix: V2D_041922_1409_JCP – Volumill Drilling problem – toolpath disappears
Bug fix: ENG_041822_1452_JCP – Save Engraving settings to roaming area
Bug fix: V2D_041822_1406_JCP – Volumill drill is not looking at breakthrough amount.

Version 7.31.49.4 (April 18, 2022)

Bug fix: STK_041322_2035_AJR – Pocketing Programs Not Updating StockModel

Version 7.31.49.2 (March 13, 2023)

Bug fix: IMP_040822_2048_JW – When UG (Prt) or Iges file is imported the text is coming in out of location.

Version 7.31.49.0 (May 03, 2022)

Bug fix: DDB_040522_1311_JCP – Problem with using the Ø Character in Rtm DB's – these characters (ALT 0216) are being changed to “O” in the DB
Bug fix: PDB_040522_1908_JCP – Problem with Zsecurity from Pocket macros

Version 7.31.48.6 (August 19, 2022)

Bug fix: ZCS_033122_1341_JCP – Zsolid should cut both block when the stock model blocks are merged.
Bug fix: V2D_033122_1441_JCP – Volumill Drilling is not adding entry inc to the drill cycle

Version 7.31.48.4 (June 24, 2022)

Bug fix: ZCS_032922_1441_JCP – Problem with “improve undercut” causing missing slices
Bug fix: CVP_032822_1658_JCP – Add Minimum Corner Rad for Curve 2d
Bug fix: STK_032922_1650_JCP – Problem updating stock model with facemill
Bug fix: STP_032822_1942_JCP – The user is unable to make a A-90 B90 setup
Bug fix: MSC_032822_1928_JCP – Problem with violation check

Version 7.31.48.1 (April 12, 2022)

Bug fix: STK_032322_1818_AJR – STL Stock Import Problem
Bug fix: STK_032122_2019_JCP – Stock model does not rotate
Bug fix: V2D_032222_1252_JCP – Problems with open sided pockets.
Bug fix: V2D_032222_1247_JCP – Problem with Volumill remachine
Bug fix: MSC_032222_1411_JCP – Rtm file did not save the pockets correctly – they are missing from one reference.

Version 7.31.48.0 (March 22, 2022)

Bug fix: DDB_032122_1700_JCP – Problem with database download to tmp, and config saving the correct DB level
Bug fix: SIM_031722_1421_JCP – Problem with bent tool

Version 7.31.47.7 (March 21, 2022)

Bug fix: MSC_030922_1633_JCP – Model Coordinate not to setup

Version 7.31.46.4 (March 08, 2022)

Bug fix: PST_022422_1602_JCP – Head is reversed on 90

Version 7.31.46.3 (March 08, 2022)

Bug fix: V2D_022322_1832_JCP – Problem with Volumill open pocket geometry

Version 7.31.46.1 (April 12, 2022)

Bug fix: STK_031122_1841_JW – Rotating this part with the stock model using the Define Assembly UCS Flip align Center, we are not rotating the stock model. Plus the Stock disappears.
Bug fix: CVD_032222_0252_JW – When you use a Drill\Curve and cut an angle we are violating the job. Simulate the CRV001 you will see it violates. If you recalculate teh CRV001 it will warn of the violation.
Bug fix: FLT_032122_1701_JW – When flowcut is calculated we are NOT displying the Collision\violation. Will not allow the file to be posted due to the collision.
Bug fix: SIM_021822_1414_JCP – Problem with head offset in configuration of new head

Version 7.31.46.0 (March 30, 2022)

Bug fix: DRL_021422_2114_JCP – Violation status appears not to be correct.
Bug fix: CVP_021122_1523_JCP – Multipass Curve 2d in pocket manager not optimizing rapids
Bug fix: RMP_021422_1459_JCP – Problem with tolerance on Ramp 2d

Version 7.31.45.1 (August 03, 2022)

Bug fix: ZCS_021022_1513_JW – Z-Cut Solid using a 2“ bullnose tool will not cut all the way to the bottom of the model. Used a surface and a window same results.
Bug fix: V2D_021022_1517_JCP – Volumill drilling not respecting Zsecurity correctly
Bug fix: V2D_021022_1510_JCP – Drill Entry not being located properly

Version 7.31.45.0 (April 05, 2022)

Bug fix: ZPT_021822_0852_ALE – ZCutPart Incomplete Mill File Using a Group Of Windows
Bug fix: PK3_021822_0944_ALE – NO Pocket 2D Remachining Mill File Using CAM Curve

Version 7.31.44.1 (February 07, 2022)

Bug fix: IMP_020122_1610_JCP – When the user imports an excel file for the strategies – the user gets an error that they can't get out of, it's in a loop.

Version 7.31.44.0 (August 03, 2022)

Bug fix: ZPT_020222_1806_JW – Z-Cut part in 3-D Milling is not using the Ramp that is setup. No Ramp angle option in the “Open Curve Options”
Bug fix: DRL_013122_1240_JCP – Problem with violation hiding the collision
Bug fix: CVD_020122_1646_JW – When a tool radius is used in the Driil\Curve 2D is not cutting to size. If you use the same tool and Z-Cut Part the hole it cuts to size. Driil\Curve 2d with 0.00 rad cuts to size also.

Version 7.31.43.1 (January 26, 2022)

Bug fix: FIX_012422_1532_JCP – Problem with point selection in Fixture setup

Version 7.31.43.0 (March 08, 2022)

Bug fix: SIM_012622_2009_JCP – Problem with head rotation being backwards
Bug fix: ZPT_012522_1502_JW – If you cretae a Z-Cut Part with a tool with a 0.00 radius goes right through the part. Add a Raduis it works correctly.

Version 7.31.42.0 (January 21, 2022)

Bug fix: FIX_011722_1631_JCP – In some cases, the user can't load a fixture plate after creating it
Bug fix: DRL_011622_0107_JCP – Multi Drill recalc doesn't recalc all axis, just the selected one

Version 7.31.41.1 (August 03, 2022)

Bug fix: ZPT_011822_2043_JW – Z-Cut Part will not go below the surface if you use the amount of the Tool Radius for the End point. Use a .001 lager or smaller it appears to work.

Version 7.31.41.0 (April 12, 2022)

Bug fix: CTP_022422_1140_ALE – Insert Center Operation using Pocket Macro
Bug fix: PSN_022222_1634_ALE – Pending Calculation Inside Pocket Manager
Bug fix: GRA_010622_1542_JCP – Dev Express
Bug fix: MSC_011322_2134_AJR – DiePlate Problem with Drill Patterns
Bug fix: ENG_011322_2124_JW – When you modify engrave it is putting it at X0 Y0 Z0.
Bug fix: MSC_011222_2116_JCP – Tool Database Feeds and Speeds are missing after using creation mode – the before and after files are attached.
Bug fix: HEL_011122_1601_JCP – Helical is not updating the stock model correctly
Bug fix: HEL_011322_1331_JCP – Depth problem with helical when using a fixed depth and tip comp
Bug fix: PST_011122_1526_JCP – Collision is not blocked from posting when several pockets are selected
Bug fix: STP_011122_1532_JCP – Problem changing holes to another setup
Bug fix: DRL_011122_1549_JCP – Multidrill is not making any mil files

Version 7.31.4 (May 16, 2023)

Bug fix: CDT_031521_1505_JCP – Circle detection not wanted on Runner system in mold
Bug fix: ZCS_031821_1706_JCP – Problem with Zsolid Entries at the bottom of the path – it also took very long to calculate – over 1 hour.
Bug fix: MSC_031521_1510_JCP – We are missing a feedrate when this file is posted – if you validate the hole, and redrill, its fixed
Bug fix: MSC_031921_1432_JCP – Tool DB Dissapeared – these files are the result – the .backup are the originals
Bug fix: ZCS_031621_1559_JCP – Zsolid file only
Bug fix: ZCS_031521_1620_JCP – Entire stock are not cut
Bug fix: ZCS_031521_1248_JCP – Problem with missing slices

Version 7.31.39.0 (September 07, 2022)

Bug fix: MSC_121721_1041_ALE – Wrong Setup Documentation
Bug fix: STK_121521_1523_JCP – Problem with Importing STL files from Powermill to the stock model
Bug fix: PRB_121421_1913_JCP – This is a request to allow the picking the center of drill circles for bottom probe points in pockets.
Bug fix: PK2_121421_1929_JCP – TrIm pocket by flat surface works correctly, but the pocket is shown incorrectly
Bug fix: DRL_120721_1904_JCP – Problem with reverse macro in multidrill

Version 7.31.38.3 (January 03, 2022)

Bug fix: DRL_120121_1646_JCP – recalc not working
Bug fix: DOC_120221_1414_JCP – Drill estimate outputting the wrong diameter in some cases

Version 7.31.38.2 (December 03, 2021)

Bug fix: DRL_120121_1413_JCP – Problem with coolant in post with secondary drills (apply) being output with post when auto tool update is on

Version 7.31.38.1 (February 07, 2022)

Bug fix: DRL_112221_1612_AJR – Collision Status changes when Validating Validation
Bug fix: FIX_112221_1518_JCP – Error displayed when removing a model from a fixture
Bug fix: PST_111821_1255_JCP – Post is outputting the <END> statements for each hole – if I include

Version 7.31.38.0 (December 01, 2021)

Bug fix: PED_111621_1450_JCP – Problem trimming pocket with surface

Version 7.31.37.2 (December 01, 2021)

Bug fix: FIX_111021_1548_JCP – Unable to save Fixture plate when FIxture.ZXT doesn't already exist

Version 7.31.37.0 (November 08, 2021)

Bug fix: PST_110821_1431_JCP – Problem adding 360 to the setup

Version 7.31.36.0 (November 12, 2021)

Bug fix: PK2_110221_1524_JW – When you select the Center Drill or Drill option in pocketing this error message appears. System is locked up. then you have to use the Task manager to close the software.
Bug fix: PST_110321_1406_JCP – Camcurve offset not working in combination with use sub program
Bug fix: MSC_110221_2043_JCP – Problem with 3D tree when recalcing program
Bug fix: STP_110121_1832_JCP – Problem with setup after reloading a file

Version 7.31.35.0 (November 02, 2021)

Bug fix: MSC_102721_1325_JCP – Rtm Is crashing when editing a holder inside RTM

Version 7.31.34.1 (January 12, 2023)

Bug fix: STK_102121_1911_JCP – Unable to import STL file
Bug fix: DDB_101921_1437_JCP – Problem with modify macro and deactivated operation

Version 7.31.33.2 (October 14, 2021)

Bug fix: FLT_101421_1430_AJR – Bad Movement Between Posted Pockets
Bug fix: GDR_101321_1558_JCP – Internal error when trying to drill

Version 7.31.32.5 (February 11, 2022)

Bug fix: ZCS_100721_1537_JCP – Zsolid cuts right through the part.
Bug fix: CDT_100721_1442_JCP – Circle not being detected that maybe should be.
Bug fix: PK2_100721_1446_JCP – REmachine tools not selecting correctly
Bug fix: MPL_100721_1635_JCP – MPM not respecting “keep MPM order”

Version 7.31.32.4 (April 28, 2022)

Bug fix: SPT_100521_1559_JCP – New Profile milling not working correctly with corner undercut ..
Bug fix: PSN_100521_1649_JCP – Pocket detection tolerance

Version 7.31.32.3 (October 18, 2021)

Bug fix: PSN_100421_1425_JCP – Pocket detection tolerance is too high for the customers pockets.
Bug fix: RMP_100421_1534_JCP – Ramp 2d is not using the default arc angle and radius from the parameter file.
Bug fix: MSC_100321_1526_ALE – Not able to translate/Copy engraving that already exists
Bug fix: PST_100321_1530_ALE – RTM generate a wrong ISO output file creating a dangerous line

Version 7.31.32.2 (December 01, 2021)

Bug fix: MSC_092921_1637_JCP – Problem opening RTM file in the newer version – just some files.

Version 7.31.32.0 (October 05, 2021)

Bug fix: SIM_100421_2131_JCP – Simulation is not working at all in the latest version – Rtm just drops from the screen
Bug fix: DDB_093021_1508_AJR – Internal Error Modify Macro

Version 7.31.30.2 (September 22, 2021)

Bug fix: CBN_091621_1641_JCP – In 3d/2d Curve milling, when trying change the start point, its not possible to make a closed curve as in V6 or the pocket manager

Version 7.31.30.1 (September 22, 2021)

Bug fix: ZPP_091521_2007_JCP – zpart has problem machining in pocket with island – machining and remaching areas it shouldn't
Bug fix: PST_091521_1858_JCP – When a machine is selected in RTM, the PPP .exe file is not being copied to the TMP folder, so wqe get an error posting
Bug fix: PMG_091521_2137_JCP – Radial Pattern not using right center point when making the program on an angle

Version 7.31.30.0 (September 22, 2021)

Bug fix: MSC_091521_1300_JCP – Fix the problem with Rtm closing
Bug fix: GRA_091421_1322_JCP – Return tool axis camera to interface

Version 7.31.3 (August 23, 2022)

Bug fix: V3D_032521_1255_JW – When you check to “Update stock Model” on the Volumill-3D program it gets to 100% of the Update Stock Model and stays there forever. Update manually and it works.
Bug fix: DRL_102121_1858_JCP – Multidrill is allowing selection of items it shouldn't
Bug fix: PST_032221_1532_JW – The text is not being updated in the post when you use the special sequence 1. Its putting some random job numbers in the field that are not the correct jobs.
Bug fix: PSN_030821_2115_JCP – New Incremental option for pocketing and chamfering
Bug fix: STK_030821_1914_JCP – Add capability to put probe points on stock model (surface normal drag function)
Bug fix: STK_030821_1913_JCP – Add capability to measure stock models (points on Stock model triangle corners)
Bug fix: ZCS_030821_1647_JCP – Zsolid slow with 0 stock
Bug fix: MSC_030821_1904_JCP – Problem saving files with long name/path
Bug fix: PRB_030821_1848_JCP – Probing <ZE> not correct – needs some work on the collision check as well.
Bug fix: STK_030821_1908_JCP – Add new feature to stock model creation

Version 7.31.29.3 (September 16, 2021)

Bug fix: MSC_091021_2057_JCP – Problem with Manufacturing setting when using a server – try to open the Manufacturing setting with Version 7.31.29.2
Bug fix: ZCS_091021_1607_JW – Z-Cut Solid remaichine using stock Model crashed into the job in a rapid move. Mil file reports no violations. Posted file reports Violation.

Version 7.31.29.2 (September 13, 2021)

Bug fix: TAG_091221_0954_ALE – RTM doesn't recognize the DP library elements
Bug fix: TAG_091221_1000_ALE – RTM doesn't recognize the DP library elements with DXF files

Version 7.31.29.0 (September 16, 2021)

Bug fix: MSC_090821_2116_AJR – Mirror Program Problems

Version 7.31.28.1 (November 02, 2021)

Bug fix: STK_083121_1246_JCP – SAmple file for Volumill Collision

Version 7.31.28 (December 01, 2021)

Bug fix: CDT_083121_1348_AJR – Circle Detection Error
Bug fix: PK2_083121_1431_JCP – Pocket manager produces an error, then hangs
Bug fix: PST_082921_0100_JCP – The latest change in arcfitting is casuing a problem in Z solid.
Bug fix: CAM_083121_1336_JCP – Translate copy camcurve doesn't work correctly.

Version 7.31.27 (February 07, 2022)

Bug fix: ZCS_082421_1400_JCP – Zsolid pocket option, is using the curve option when set to plunge.
Bug fix: CFP_082521_1318_JCP – Chamfer2d is still producing a program after warning the tool is too short, then violates the part
Bug fix: MSC_082421_1320_JCP – Deleting the process list causes an error

Version 7.31.25 (October 13, 2021)

Bug fix: PST_100821_1529_JCP – Multimill file has a posting problem
Bug fix: MSC_100821_1539_JCP – Collision report is causing RTM to crash
Bug fix: TAP_081921_1355_AJR – Tap not posting in 7.31.25
Bug fix: PK2_082521_1445_JW – Pocket mgr Flat 2D Rapid move cuts through job with no violation detected.
Bug fix: THR_081821_1430_JCP – Thread milling arcfit is not outputting constant numbers – also rough thread mill is not arcfit, and takes a long time to post
Bug fix: DRL_082021_2057_JW – When you add the “Set Extremity Stock” we are not applying it to all the holes.. See pics.
Bug fix: PST_082021_1348_JW – When holes are straight on a setup you cannot Right Click on the setup and select Drill. If the holes are on an angle you can right click setup and choose drill.
Bug fix: ZCS_081821_1239_JCP – Collision avoidance works in a windows, but not with the entire model
Bug fix: ZCS_081821_1227_JCP – Unable to post in the lastest version 7.31.25

Version 7.31.24 (October 04, 2021)

Bug fix: IMP_081121_1603_JCP – This is a request to save the Iges file that is created by Datakit to a specific folder
Bug fix: PK2_080621_1917_JCP – Not-Continuous error on two pockets.
Bug fix: PK2_081121_1447_JCP – arcfitting seems to have a poor result with this file

Version 7.31.23 (September 07, 2022)

Bug fix: PKM_071321_2010_JCP – Mirror pockets with programs are not using the default Z security plane.
Bug fix: V2D_080221_1929_JW – Volumill in Pocket Mgr with open sided pocket selected produces an error everytime.
Bug fix: ZCS_072621_1937_JCP – Zsolid not using correct start height
Bug fix: STK_072621_1550_JCP – Stock model update problem
Bug fix: STK_072321_2008_AJR – STL Import problem for Stock Model
Bug fix: PST_072221_1450_JW – Posted file is not reading the correct retract value. Crashed into the part.
Bug fix: CFP_071521_1324_JCP – Chamfer in the pocket manager hangs if you pick the bottom edge only
Bug fix: PKM_071321_1953_JCP – Coolant switch settings are not being saved in pocket macros
Bug fix: CAD_072821_1933_JCP – translate copy is not moving things to the correct distance
Bug fix: MPL_072821_1917_JCP – Problem posting MPM files – the process will hang.
Bug fix: PST_071221_2001_JCP – Post Optimize is hanging when trying to output more than one facemilling programs at a time

Version 7.31.22 (August 23, 2021)

Bug fix: FLT_070821_2014_JCP – Flat 2d remachine is not working at all
Bug fix: MSC_071221_1300_JCP – Violation checking is not working correctly
Bug fix: ZPT_071221_1257_JCP – Zpart is not cutting all area as it was in previous versions.
Bug fix: GRA_070221_1648_JCP – Improve the drill manager picking when picking the same pattern from forward to reverse ..

Version 7.31.21 (August 05, 2021)

Bug fix: ZCS_062921_1231_JCP – Collsion avoidance toolpath shows collision with new algorithm
Bug fix: STP_062921_2048_JCP – Problem with alternate rotations in the drill manager
Bug fix: MSC_062921_1958_JCP – Wrong Operation name in the process list
Bug fix: CDT_062921_1923_JCP – The user would like to be able to add multiple circles at the same time
Bug fix: CAM_062521_1942_AJR – Bad Camcurve Creation
Bug fix: DDB_062921_1953_JCP – Drill Manager structure error giving a false warning
Bug fix: CHD_062921_1927_JCP – Bad Zsecurty when using post optimized or multiplate

Version 7.31.20 (August 23, 2021)

Bug fix: STK_062321_1237_JCP – Z Part Not updating stock model correctly
Bug fix: ZCS_062421_1319_AJR – Zsolid Entry Problem with Collision avoidance
Bug fix: PSN_062121_1557_AJR – Mill pockets without model generated
Bug fix: CAM_062421_2155_AJR – Camcurves not captured when in side view
Bug fix: MSC_062221_1409_JCP – Collision report is showing a translated (offset) graphic of the collision area on the head.
Bug fix: DRL_062321_1535_JCP – REquest to move the “delete” button in the drill manager

Version 7.31.2 (March 08, 2022)

Bug fix: V2D_030321_1920_JCP – Volumill errors out when making an open sided pocket
Bug fix: DRL_030821_1629_AJR – Drill Individual not saving changes
Bug fix: MSC_022621_1514_ALE – Text missing in English Message for translation
Bug fix: DOC_022621_1422_ALE – The documentation is not working correctly when path name is too long
Bug fix: DRL_030321_1811_JCP – Delta is having a problem with RTM files that have a drill status but are not show ing the programs

Version 7.31.19 (September 26, 2023)

Bug fix: 3DM_061721_2102_JW – When building a 3D Macro we are not allowing the Stock Model to be seleted even though its the first operation.
Bug fix: 3DM_061721_2122_JW – Add the option to Create External Boundary or offset an existing one inside the 3D Macro
Bug fix: DR3_061721_2010_JW – Selecting holes in 3-D drilling by Diameter or color is not selecting all the holes.
Bug fix: 3DM_061721_2111_JW – When Variable Stock is used in a Macro we are not closing the Variable stock window. It stays on the screen until Lemoine is shut down.
Bug fix: 3DM_061121_1645_JW – The Update Stock Model does not work in the Lace cut, Drag Cut in the Macros. The Update Stock model was selected in all operations in the Testing Macro.
Bug fix: MSC_061421_1549_JCP – Request for log output of licensing
Bug fix: MSC_061621_1640_JCP – When Pulse.txt is on, use info panel for Editor of file after posting – open info , before outputting path for pulse

Version 7.31.18 (June 16, 2021)

Bug fix: DOC_061021_1955_JW – Drilling Estimate is not outputting the correct information. Patterns are coming out with 00.00.00 Runtimes. Micro Auto uses this for their quoting.
Bug fix: ZPT_060721_2259_JW – Evrey Z-Cut part is giving a Violation. I have tried multiple things but I keep getting violations in different locations.. Happens In 3D and Pocket manager

Version 7.31.17 (November 29, 2022)

Bug fix: MSC_060121_1643_JCP – Collision check misses a collision with helical
Bug fix: DRL_060121_1831_JCP – Strange References in the drill manager
Bug fix: MPL_053121_1449_JCP – Multiplate not outputting Zsecurity correctly
Bug fix: PED_053121_1511_JCP – Pocket heights incorrect in set top/bottom

Version 7.31.16 (July 13, 2021)

Bug fix: PST_060121_2005_JW – The process list has alot of Red Text and will not allow the files to be posted with the rest of the process list.

Version 7.31.15 (June 14, 2021)

Bug fix: DDB_052021_2034_AJR – Copy and Paste Macro Not Working
Bug fix: ZCS_051821_1820_JCP – ZSolid Missing slice/violation problems.
Bug fix: PED_051421_1950_JCP – Set Top and Bottom for pockets (ABS) is not working correctly with multiple pockets
Bug fix: MPL_051721_1631_JCP – Multiplate is not optimizing

Version 7.31.14 (May 25, 2021)

Bug fix: PST_051321_1913_JCP – Post optimize has improper rapids causing an incorrect output
Bug fix: MSC_051321_1929_JCP – Zsecurity not respecting users choice correctly
Bug fix: PMG_051421_1028_JCP – Multiplate crashes when you try to post engraving.

Version 7.31.12 (October 04, 2021)

Bug fix: IMP_050721_1939_JCP – Problem converting multiple step files using RTMCMD … I get an .ENV file missing error
Bug fix: PK2_043021_1608_JCP – Problem with remachine in pocketing
Bug fix: PST_050721_1413_JCP – Problem with post optimize retracts between holes
Bug fix: PK2_050521_1352_JCP – Problem with ramping in pocketing
Bug fix: PK2_050521_1350_JCP – Probem with pocketing not staying on the correct level
Bug fix: PST_050621_1337_JCP – Post optimize from the process list has the wrong list of files
Bug fix: MSC_050321_1600_JCP – Database selection not updating until you change machines

Version 7.31.11 (April 18, 2022)

Bug fix: CAD_042321_2027_AJR – Drilling Shade Translucene bar not working in CAD
Bug fix: CDT_042721_1424_AJR – Circles not detecting
Bug fix: PSN_042721_1648_AJR – Pocketing Problem after Edit Setup
Bug fix: MSC_042621_1421_JCP – Process List is not working correctly

Version 7.31.1 (February 16, 2021)

Bug fix: STP_021521_1609_JCP – Setup, and edit Setup seems to have a problem with the colour reference and the white reference

Version 7.31.0 (February 11, 2021)

Bug fix: PST_021021_2126_JCP – Problem with scaling factor
Bug fix: DRL_020921_2149_JCP – Problem with the new tolerance check

Version 7.30.9 (February 12, 2021)

Bug fix: PRB_020121_1338_JCP – Add default probing distance to parameter file.
Bug fix: PST_020221_2023_JCP – Allow enable/disable tools in ATC manager
Bug fix: DDB_020421_2012_JCP – Macro Database not updating from server correctly with empty TMP folder
Bug fix: MSC_020421_2002_JCP – Problem with Config not remembering setting
Bug fix: CDT_020221_2013_JCP – Change to Parameter.exe to allow a lower minumum
Bug fix: DDB_020221_2009_JCP – Problem seeing complete list of drill operations when there are too many UCD's both in the dp editor and RTM

Version 7.30.8 (February 15, 2021)

Bug fix: CDT_012921_1548_ALE – Problem with circle detection out of position
Bug fix: CAD_013021_1758_JW – CAD- Intersect 2 surfaces is causing an error. But still is giving the correct results.
Bug fix: HEL_012821_2002_JCP – Helical For this post is outputting strange numbers – mostly 0 – we have this at 2 customers already
Bug fix: PST_012721_1701_JCP – Post processor not scaling RPM to post maximum –only in Gundrill Slow RPM

Version 7.30.7 (February 10, 2021)

Bug fix: STK_011821_1942_JCP – Stock model has problems updating when we use TrimXY on the stock model – I suspect its the 1mm missing at the bottom.
Bug fix: PST_012621_1420_JW – When the Tool-Last (In the POST\FORMAT\SYNTAX)is set to “First” we are using the tools reference number instead of the ATC number.
Bug fix: ZCS_012521_1919_JCP – Zsolid gouges the stock with S move
Bug fix: FCM_012521_1310_AJR – Facemill leaving double stock
Bug fix: PRB_011821_2004_JCP – The chain that connects the probe point to the model should be in simulation and collision checking

Version 7.30.6 (August 13, 2021)

Bug fix: DRL_011321_2001_JCP – Add new functionality to the operation filter for blind and through holes
Bug fix: MSC_011121_2027_JCP – Add new button to select background colour
Bug fix: MSC_011121_1929_JCP – Request For Cheto Tool Offsets
Bug fix: PST_011121_2024_JCP – Add Assembly name to columns in post dialogue
Bug fix: MSC_011121_1949_JCP – Assembly Warning For non-assembly in tool selection
Bug fix: DRL_011121_2104_JCP – Tagged holes appear to be correct, but the reference for these holes is wrong by a large amount –making the drilling wrong

Version 7.30.5 (March 17, 2021)

Bug fix: ZCS_012521_1332_AJR – Variable Depth in Z-Solid Not Working with Grouped Windows
Bug fix: PST_010421_1840_JCP – Please add a new variable in the start of operation called <HOLN> from the number of holes in the current mil file.

Version 7.30.2 (February 02, 2021)

Bug fix: STK_120120_1317_JCP – Trim XY has a problem with stock

Version 7.30.0 (August 05, 2021)

Bug fix: STP_111920_1312_AJR – Machine Setup Losing Data
Bug fix: CAD_111620_1256_JW – Trim a surface using a curve it is creating a square instead of trimmimg the circle out.

Version 7.20.37 (March 22, 2021)

Bug fix: IMP_110220_1925_JW – We are giving the Absolute & Relative dimensions for the cad curves and not just the surfaces.

Version 7.20.36 (April 23, 2021)

Bug fix: STP_102720_2047_JCP – Can't seems to split patterns to a new C angle rotation.

Version 7.20.25 (August 08, 2022)

Bug fix: GRA_082020_1410_AJR – Hidden Windows - Have to force close RTM
Bug fix: STK_081020_1632_AJR – Stock model adding stock to Z-

Version 7.20.24 (July 07, 2022)

Bug fix: DRL_080620_1906_AJR – Multi_Drill Not drilling all holes together

Version 7.20.23 (April 23, 2021)

Bug fix: WDW_072420_1909_AJR – Functions missing with grouped windows

Version 7.12.93 (October 07, 2024)

Bug fix: MSC_082824_0503_JCP – Emergency Problem with create spotface – function is not working correctly in the latest version

Table of Contents

Version 7.51.11.67 (December 05, 2024)

Version 7.51.11.65 (December 05, 2024)

Version 7.51.11.63 (October 21, 2024)

Version 7.51.11.62 (December 05, 2024)

Version 7.51.11.61 (December 05, 2024)

Version 7.51.11.59 (October 11, 2024)

Version 7.51.11.55 (October 07, 2024)

Version 7.51.11.51 (October 07, 2024)

Version 7.51.11.49 (October 07, 2024)

Version 7.51.11.48 (October 07, 2024)

Version 7.51.11.44 (August 13, 2024)

Version 7.51.11.41 (August 12, 2024)

Version 7.51.11.40 (October 07, 2024)

Version 7.51.11.39 (August 12, 2024)

Version 7.51.11.38 (August 12, 2024)

Version 7.51.11.36 (August 12, 2024)

Version 7.51.11.34 (March 26, 2024)

Version 7.51.11.33 (March 26, 2024)

Version 7.51.11.30 (March 26, 2024)

Version 7.51.11.27 (March 11, 2024)

Version 7.51.11.25 (March 11, 2024)

Version 7.51.11.24 (March 11, 2024)

Version 7.51.11.16 (February 26, 2024)

Version 7.51.11.11 (March 08, 2024)

Version 7.41.12.9 (November 17, 2023)

Version 7.41.12.7 (October 07, 2024)

Version 7.41.12.6 (November 10, 2023)

Version 7.41.12.4 (December 04, 2023)

Version 7.41.12.13 (November 17, 2023)

Version 7.41.12.0 (November 10, 2023)

Version 7.41.11.6 (October 10, 2023)

Version 7.41.11.2 (September 19, 2023)

Version 7.41.11.12 (November 02, 2023)

Version 7.31.9 (June 14, 2021)

Version 7.31.8 (May 11, 2021)

Version 7.31.7 (August 06, 2021)

Version 7.31.68.9 (September 26, 2023)

Version 7.31.68.7 (June 23, 2023)

Version 7.31.68.4 (May 25, 2023)

Version 7.31.68.23 (September 19, 2023)

Version 7.31.68.22 (September 26, 2023)

Version 7.31.68.20 (September 26, 2023)

Version 7.31.68.2 (June 20, 2023)

Version 7.31.68.19 (September 19, 2023)

Version 7.31.68.18 (July 25, 2023)

Version 7.31.68.16 (July 19, 2023)

Version 7.31.68.15 (July 25, 2023)

Version 7.31.68.1 (May 25, 2023)

Version 7.31.68.0 (May 03, 2023)

Version 7.31.67.8 (May 25, 2023)

Version 7.31.67.5 (June 23, 2023)

Version 7.31.67.3 (April 10, 2023)

Version 7.31.67.14 (September 26, 2023)

Version 7.31.67.11 (May 10, 2023)

Version 7.31.67.1 (March 28, 2023)

Version 7.31.67.0 (November 10, 2023)

Version 7.31.66.9 (March 10, 2023)

Version 7.31.66.7 (March 10, 2023)

Version 7.31.66.5 (June 23, 2023)

Version 7.31.66.3 (September 19, 2023)

Version 7.31.66.15 (March 27, 2023)

Version 7.31.66.11 (March 28, 2023)

Version 7.31.66.1 (March 03, 2023)

Version 7.31.65.9 (February 01, 2023)

Version 7.31.65.8 (January 18, 2023)

Version 7.31.65.3 (January 11, 2023)

Version 7.31.65.0 (January 04, 2023)

Version 7.31.64.0 (December 22, 2022)

Version 7.31.63.2 (February 15, 2023)

Version 7.31.63.0 (December 08, 2022)

Version 7.31.62.3 (October 12, 2023)

Version 7.31.62.15 (April 10, 2023)

Version 7.31.62.13 (November 29, 2022)

Version 7.31.62.11 (November 29, 2022)

Version 7.31.62.1 (October 07, 2024)

Version 7.31.61.8 (October 12, 2023)

Version 7.31.61.7 (April 01, 2024)

Version 7.31.61.5 (October 19, 2022)

Version 7.31.61.1 (October 12, 2022)